Wrought iron
Wood & steel frame
Farm & ranch
Sliding driveway gates
LiftMaster operatorsFree on-site gate assessment - hinges, posts, and your LiftMaster or Nice gate operator checked before anything is quoted
The assessment is free and the quote is the invoice.
Get your free estimateGate Company in Brea, CA
Gate installation in Brea usually means one of two jobs: replacing a rusted 1970s-era driveway gate on a tract home north of Imperial Highway, or engineering a heavier custom gate for a hillside lot in the 92823 ZIP code where Santa Ana wind load changes the spec. We are First Light Gate Repair, and gates are the only trade we work in. From first measure to final swing test, we handle the full installation on your property in Brea. Call (833) 734-5599 for a free measure and written quote.
Why Brea Homes Are Different
Brea sits where the flat LA basin butts up against the Chino Hills. That boundary does more than shape the view. It shapes the work. Homes in the flatter tracts of 92821 and 92822 tend to sit on standard lots with standard setbacks, but once you climb into the hills above Carbon Canyon or into the 92823 ridges, wider lots mean longer gates, heavier leaves, and longer runs of track on sliding systems. A gate that would be a simple drop-in replacement on a flat basin lot becomes a wind-load calculation on a hillside.
The housing stock matters too. Much of Brea was built during the 1960s through the 1980s, a stretch tied directly to the old Union Oil and Brea Oil Field land. What that means for us on a daily basis: original wrought-iron and chain-link driveway and pool gates that are now rusting at the hinge line, sagging on the latch post, or far out of current child-safety compliance. Homeowners frequently call us for a new gate installation because the old one failed a home inspection or an HOA notice, not just because it looks tired.
And the HOAs in Brea are active. In the master-planned communities south of Imperial Highway, gate style, height, color, and even the direction of swing are often prescribed in the CC&Rs. We check setback and HOA requirements before quoting any swing. A tech who has only worked neighboring cities won’t know that a gate can’t be sited where the homeowner assumes it can, especially on older properties around the former oil field with unusual lot lines and easement fencing.
Styles & brands we work with
Our Main Brea Services
Most Brea homeowners call us for one of two reasons: a gate that stopped working correctly, or a gate they want installed to replace something old, rusty, or HOA-flagged. Both live under one roof here, and both are covered below with links to their own Brea pages.
Gate Repair in Brea
Older steel gates in Brea take a beating from dry summer heat, winter rain rust, and the Santa Ana winds that arrive each fall and winter. Hinges sag, latch posts rot or lean, and weld points crack on the side that catches the wind. We repair the gate to close square and latch securely, which usually means re-setting or replacing hardware rather than chasing a patch job. Our techs work across LiftMaster, FAAC, Linear, and Viking systems, plus five other major brands. Read the full detail on our Gate Repair in Brea page.
Electric Gate Repair in Brea
An automatic gate that won’t open is an access problem, not just an annoyance, and Brea has enough of these systems on hillside and HOA properties that we see the failure patterns clearly. Most electric gate failures trace to the operator, the control board, or a limit switch that drifted out of adjustment, not the gate itself. Our team diagnoses across brand platforms instead of reading from one manufacturer’s playbook: FAAC and BFT on the commercial side, LiftMaster and Linear on residential, DoorKing and Elite in between. For the full breakdown, visit Electric Gate Repair in Brea.
What happens when you call
- 1
A real person answersNo phone trees — you reach a local pro.
- 2
You get an upfront price rangeHonest numbers before anyone is dispatched.
- 3
A background-checked tech heads outLicensed & insured, dispatched right away.
- 4
You approve before work beginsNothing starts until you say go.
Gate Installation in Brea
Gate installation in Brea is often driven by one of three pressures: an HOA notice requiring a compliant gate style, a rusted-out original from the 1960s-to-1980s housing stock, or a homeowner in the 92823 hills who wants a wider, heavier gate that matches the lot. The terrain and wind exposure change how we size the posts, the hinges, and the operator. We measure, set, hang, and test every installation as a complete system. For the wider picture on how we approach this trade, see our Gate Installation page.
Automatic Gate Installation
Signs you need it
You’re opening a heavy driveway gate by hand every day, or an existing automatic operator has failed and the gate is now a manual chore.
What it costs in Brea
Automatic gate installation in Brea typically runs between $3,200 and $9,500 depending on gate size, operator brand, and access-control needs.
How we do it
We set the posts and gate leaf first, then mount the operator, run power, wire the safety edges and keypad or intercom, and test full open-close cycles before we leave.
Driveway Gate Installation
Signs you need it
Your existing driveway gate is rusted through at the hinge line, sagging past the latch, or so far from current HOA spec that patching it no longer makes sense.
What it costs in Brea
Driveway gate installation in Brea typically falls between $1,800 and $7,200 depending on gate material, width, and whether power is needed.
How we do it
We verify setback and HOA requirements, set posts in concrete at the correct depth, hang the gate, and adjust the swing so it latches cleanly without binding.
What Gate Installation Costs in Brea
| Item | Typical range in Brea |
|---|---|
| Manual driveway gate (single swing) | $1,800 – $4,200 |
| Automatic gate with operator | $3,200 – $9,500 |
| Sliding gate on steel track | $2,600 – $8,000 |
Do you handle the power run and safety edges on a new automatic gate?
Yes. We run the electrical supply to the operator, install the safety edges or photo-eye sensors, and connect the keypad or intercom. Nothing gets handed off to a second contractor.
Can you install a gate that matches an HOA spec in Brea?
We can. We review the governing documents or the HOA approval letter with you, then quote a gate that matches the required style, height, and color before any material is ordered. Call (833) 734-5599 for a free measure.
Brands We Service in Brea
We work on LiftMaster, FAAC, BFT, and Linear gates and operators, and our Brea jobs draw on stocked parts and longer lead parts from all nine manufacturer platforms we cover. Turnaround on a parts-dependent repair depends on what the diagnostic turns up, but stocked items are usually handled the same day. See our brands for the full lineup.
See the difference
Before
After
Before
After
Before
AfterPricing for Gate Company in Brea, CA
| Service | Typical range in Brea |
|---|---|
| Gate hinge or latch replacement | $120 – $380 |
| Weld repair on a steel gate | $140 – $420 |
| Sagging gate realignment | $160 – $480 |
| Chain-link or wrought-iron gate restoration | $240 – $700 |
| Automatic gate operator replacement | $700 – $2,100 |
| Control board replacement | $350 – $700 |
| Safety sensor or photo-eye repair | $130 – $350 |
| Manual driveway gate installation | $1,800 – $4,200 |
| Automatic gate installation | $3,200 – $9,500 |
| Sliding gate installation | $2,600 – $8,000 |
In Brea, the two biggest price movers are gate width on hillside lots and how much of the old hardware has rusted through, because rust at the post often means the post gets replaced too. Whatever the job, the price is quoted and agreed before any work starts, so the invoice you see at the end is the number you approved at the beginning.
Neighborhoods We Serve in Brea
We cover all three Brea ZIP codes, 92821, 92822, and 92823, from the flat tracts north of Imperial Highway up through the hillside communities east of Carbon Canyon. Our techs are in the area regularly, and we quote same-day response whenever the schedule allows, which it usually does on weekday morning calls.
- The tracts and ranch homes north of Imperial Highway
- HOA-governed communities south of Imperial Highway
- Hillside and custom-home streets in 92823
- Neighborhoods near Carbon Canyon
- Older lots around the former Brea Oil Field
Service Area – Cities Near Brea
First Light Gate Repair runs routes through north Orange County, so when a Brea job wraps early we will often head into a neighboring city the same afternoon. We serve Placentia, CA for tract-home gate repairs, Fullerton, CA for older steel and wrought-iron work, Yorba Linda, CA for hillside and custom gates, and La Habra, CA for automatic gate operator work.
Serving Brea, CA — Our Local Coverage Area
We’re based in the Brea area and know this community well. Use the map below to see our service coverage — if you’re nearby, we can almost certainly help.
FAQs About Gate Company in Brea
We run routes through Brea regularly and will usually get to a morning call the same day. Afternoons may land next morning depending on how the calendar sits, but we always tell you straight when you call rather than making you wait to find out.
If your community requires it, yes. We check the HOA standards with you and will not order material for a gate that does not match the approved style, height, or color. We also verify setback and easement lines on older oil-field lots before quoting a swing.
All three Brea ZIP codes, 92821, 92822, and 92823, including the flat tracts, the HOA neighborhoods, and the hillside homes above Carbon Canyon. The only thing that changes by area is how the wind, terrain, and lot shape affect the gate spec.
What happens when you call
- 1A real person answersNo phone trees — talk to a local gate repair pro.
- 2You get an upfront price rangeHonest numbers before anyone is dispatched. No surprises.
- 3We come out and measureLicensed & insured, at a time that suits you — the visit and the quote are both free.
- 4You get the price in writingLine-itemed, yours to keep, and nothing starts until you say go.
What Brea Customers Say
"Gate works properly now and the price was fair. The one thing is that it took two visits, because the operator model we have is old and the part had to be ordered. They didn't charge for the second trip."
— Alejandro Guzman"Our slide gate had been dragging for months and getting worse. Turned out the chain was stretched and one of the guide rollers had seized. Both replaced, and he adjusted the limits so it stops properly at both ends now."
— Brooke Fletcher"Repair is holding. He was quite a bit later than the window I was given, and the office didn't call me about it, I had to call them. The work itself was done well once he got here."
— Karen Chen